Ets-lindgren 2165 Turntable Manual do Utilizador

Model 2165 LoPro™ Turntable 1.2-Meter User Manual

10 | Introduction This page intentionally left blank.

Maintenance | 11 2.0 Maintenance Before performing any maintenance, follow the safety information in the ETS-Lindgren Product Information Bulle

12 | Maintenance 6-MONTH SERVICE • Check all parts for wear. • The drive belt is furnished fully tensioned, but after usage the belt may need to

Maintenance | 13 Replacement and Optional Parts Following are the part numbers for ordering replacement or optional parts for the Model 2165 LoPro

14 | Maintenance This page intentionally left blank.

Specifications | 15 3.0 Specifications Electrical Specifications Nominal AC Voltage: 208–230 VAC Input Frequency: 50/60 Hz Current Rating: 3 A R

16 | Specifications This page intentionally left blank.

Turntable Installation Considerations | 17 4.0 Turntable Installation Considerations Before assembling, installing, or connecting any componen

18 | Turntable Installation Considerations The fiber optic cable must be looped through the P-clip installed on the front panel of the motor base.

Electrical Installation | 19 5.0 Electrical Installation Before assembling, installing, or connecting any components, follow the safety inform

ii | ETS-Lindgren L.P. reserves the right to make changes to any products herein to improve functioning or design. Although the information in this do

20 | Electrical Installation This page intentionally left blank.

Assembly and Installation | 21 6.0 Assembly and Installation Before assembling, installing, or connecting any components, follow the safety inf

22 | Assembly and Installation 2. After the turntable is in position, remove the plastic gearbox cover plate by loosening the four plastic bolts h

Optional Shaft Kit Installation Instructions | 23 7.0 Optional Shaft Kit Installation Instructions Before assembling, installing, or connectin

24 | Optional Shaft Kit Installation Instructions Required Tools In addition to the tools for basic installation, these additional tools are requir

Optional Shaft Kit Installation Instructions | 25 Install Shaft Housing 1. Assemble one of the two PVC outer shaft housings into one of the two

26 | Optional Shaft Kit Installation Instructions 2. Loosen the three 3/8–16 hex head screws on the gearbox coupling before insertion. Place the 1

Optional Shaft Kit Installation Instructions | 27 Cut Drive Shaft Assembly The inner drive shaft is shipped separate from the turntable and consi

28 | Optional Shaft Kit Installation Instructions Make sure to measure and mark each section from the small end, not the plain end. The length of

Operation | 29 8.0 Operation Before placing into operation, follow the safety information in the ETS-Lindgren Product Information Bulletin incl

| iii Table of Contents Notes, Cautions, and Warnings ... v 1.0 Introduction ..

30 | Operation This page intentionally left blank.

Warranty | 31 Appendix A: Warranty See the Product Information Bulletin included with your shipment for the complete ETS-Lindgren warranty for y

32 | Warranty This page intentionally left blank.

Drawings | 33 Appendix B: Drawings Your Model 2165 LoPro™ Turntable may vary slightly from the following drawings. See these drawings located in

34 | Drawings This page intentionally left blank.

EC Declaration of Conformity | 35 Appendix C: EC Declaration of Conformity The EC Declaration of Conformity is the method by which ETS-Lindgren

Drawing 11011

10 1112Drawing 2

Drawing 3(optional shaft kit shown)10 11 12

Drawing 4(optional shaft kit shown)

iv | Cut Drive Shaft Assembly ... 27 Cut Shaft Housing .

Drawing 5(optional shaft kit shown)

Drawing 6(optional shaft kit shown)

Drawing 7

Drawing 8(optional shaft kit shown)

Drawing 9(optional shaft kit shown)

Drawing 10(optional shaft kit shown)

Drawing 11

| v Notes, Cautions, and Warnings Note: Denotes helpful information intended to provide tips for better use of the product. Caution: Denotes a hazar

vi | This page intentionally left blank.

Introduction | 7 1.0 Introduction The ETS-Lindgren Model 2165 LoPro™ Turntable is an electric-powered, variable-speed turntable platform system d

8 | Introduction • Conductive top • Continuous rotation • 10-meter fiber optic control cable • Fiber optic shield penetration kit Additionally, t

Introduction | 9 SHAFT KIT This option allows the electric drive motor to be positioned farther from the turntable. The extension shaft separates t